Ultra TUFF - Technical Data

Technical Data for
Ultra TUFF Non-Skid Coating

Ultra TUFF is a state of the art, WATER BASED, SINGLE PACK acrylic/urethane copolymer with recycled rubber crumb as an aggregate. This environmentally friendly coating is extremely durable and designed to adhere to most substrates with excellent abrasion and chemical resistance rendering them non-slip. Ultra TUFF contains no VOC's, is odorless and can be applied with a roller, low pressure spray gun or airless, Typical thickness is approximately 30-40 mils. See printable spec sheet. Also, See printable warranty.

Unlike epoxies Ultra TUFF is also very flexible making it chip and impact resistant. Ultra TUFF will handle wear from foot traffic to forklift and automotive traffic. Ultra TUFF is an air dry, air cure coating and is non-flammable. Available in 19 UV resistant colors (click here for a color chart)!

KEY FEATURES:	ADHERES TO:
Water Based No VOC's Single Component (no mixing) 19 Standard Colors Chemical Resistant Salt Resistant Highly Durable Rubberized (made of recycled rubber)	Metal Concrete Painted Surfaces Aluminum Fiberglass Wood Primers

Application

Ultra TUFF in standard form can be rolled or sprayed on. No expensive equipment or complex tools are required to apply the product. Use our special Ultra TUFF Foam Roller or Hopper Gun for best results. See the application manual for details. The application manual is in PDF format, and should be readable by any recent installation of Adobe Acrobat Reader, however, if you have any problems, please download and install the latest of version of Adobe Acrobat Reader (free).

Colors

Ultra TUFF is available in 19 standard colors. Color matching is available in minimum batch sizes of 5 gallons at no extra charge. See our Color Chart for specific colors available.

Pot and Shelf Life

Ultra TUFF has no pot life. Ultra TUFF has a minimum shelf life of one year from manufacture. Partly used cans of Ultra TUFF can be re-sealed for up to one year without damage to the product. Dilution of Ultra TUFF must only be done with clean water. DO NOT USE SOLVENTS OR THINNERS. DO NOT LET FREEZE.

Curing

Ultra TUFF cures as a result of a cross linking process and evaporation and should, therefore, be touch dry in 30 minutes per coat (77°F & 50% humidity). Light traffic is possible after 10-12 hours, hard dry in 24 hours, and a full cure will take 5-7 days.

Coverage

Pending final application requirements, it is recommended that Ultra TUFF is applied at a minimum of 40-50 sq. ft. per gallon for most non-heavy commercial applications, and 35 sq. ft. per gallon for heavy industrial applications. The desired thickness is achieved in two coats for most non-heavy commercial applications and in three coats for heavy industrial applications. These coverage estimates include the multiple coats necessary to achieve desired thickness.

Surface Preparation and Adhesion

As with all coatings, Ultra TUFF adhesion is dependent on the quality of the substrate and the preparation of the substrate. All surfaces must be sound, dry, free of oil, wax, grease, and loose material. Use the Ultra TUFF Application Manual as directed.

Equipment Cleanup

Clean equipment with hot or cold water. Over-spray and application errors should be cleaned with a water damp cloth as soon as the error occurs.

Identification

Physical Description/Properties

PRODUCT NAME: Ultra TUFF
OTHER NAMES: Non-Skid Coating
UN NUMBER: N/A
D/G CLASS: N/A
HAZCHEM CODE: N/A
POISONS SCHEDULE: N/A
PACK SIZES: 1 Qt., 1 Gal., 5 Gal.
USES: Non-slip decorative and protective safety coating

APPEARANCE: Colored Liquid
BOILING POINT: 100° C
VAPOR PRESSURE: (20° C Kpa) 2.36
PERCENT VOLATILIZE: 45% w/w
SPECIFIC GRAVITY: 1.05
FLASH POINT (C) CLOSED CUP: Napp
FLAMMABILITY (%): Napp
SOLUBILITY IN WATER: Soluble

Ingredients

Chemical Properties

Entity	CAS No.	Proportion*
Urethane/Acrylic - Copolymer		31-60%
Water	7732-18-5	31-60%
Rubber Crumb		10-29%
N-Methyl	872-50-4	0.25-0.5%
Pyrrolidone Triethylamine	121-448	0.25-0.5%
Pigments & Plasticisers		1-9%
Thickeners & other minor ingredients		1-9%
* Very high is 60 or above, high is 30-60, medium is 10-29, and low is 1-9

Solids	87% by volume
pH	9
Viscosity	100-110 KU
Density	1.06-1.1

Resistance (after recovery)

Independent Tests Performed

Fuel	4
Diesel	4
Hydraulic Oil	5
20W50 Oil	5
Used Oil	5
Sulphuric Acid (10% Solution)	5
Acetic Acid (10% Solution)	5
Alkaline (Sod Hyd.)	5
Alkaline (Detergent)	5
Motor Anti-Freeze	3
Window Anti-Freeze	3
Water	5
Ethanol	5
190 Proof Alcohol	5
Ammonia	5
Solvents	4
Vinegar	5

ASTM D4541-95 Pull Off Adhesion Tests
ASTM-F-510 Wear Testing
ASTM-D-2794 Impact Resistance
UV Testing
Hot Tire Pickup Tests
ASTM-F-609 Coefficient of Friction Test

Health Hazard Information

See the printable Material Safety Data Sheet (MSDS) to make a copy of all the below information for your records.

Health Effects

No adverse health effects are expected if the product is handled in accordance with this MSDS.

SWALLOWED: No adverse effects expected. However, large amounts may cause nausea and vomiting.
EYE: May be an irritant.
SKIN: Contact with skin may result in irritation.
INHALED: Vapor may be an irritant to mucous membranes.

First Aid

SWALLOWED: Rinse mouth with water. Give plenty of water to drink. If vomiting occurs, give more water to drink. Seek medical advice.
EYE: Irrigate with copious amounts of water for 15 minutes. In all cases of eye contamination, it is sensible to seek medical advice.
SKIN: Remove contaminated clothing. Wash contaminated skin with plenty of soap and water. If irritation persists, seek medical advice.
INHALED: Remove victim from exposure. Remove contaminated clothing. Keep patient warm and comfortable until fully recovered. Seek medical advice if effects persist.

Advice to Doctors

Treat symptomatically.

PRECAUTIONS IN USE

EXPOSURE LIMITS OF CONSTITUENTS:
Triethylamine: TWA (3.0 PPM) mg/ m3 12 | STEL (5.0 PPM) mg/ m3 20

Ventilation

Local exhaust ventilation required if concentration is likely to exceed these limits. It is recommended that the product is always applied ensuring adequate ventilation.

Personal Protection

Gloves: Avoid skin contact. PVC gloves and overalls.
Eyes: Safety goggles.

Breathing apparatus may be required in confined areas which meet the requirements of AS1715 and AS1716.

Flammability

Non-combustible material.

SAFE HANDLING INFORMATION

Storage and Transport

No hazmat restrictions. No shipping restrictions. Store in closed containers in well ventilated areas away from direct sunlight. Store between 5 C and 40 C. Keep from freezing.

Spills and Disposal

Slippery when wet. Use protective clothing. Contain spill with sand, soil, or other inert material. Collect and seal in properly labeled drums for disposal. Wash area with detergent and excess water. Disposal: Refer to State Land & Waste Management.

Fire/Explosion Hazard

Not combustible. However, following evaporation of aqueous component residue, material can burn if ignited. Water can be used to cool closed containers to prevent pressure build up. Fire fighters to wear self contained breathing apparatus if at risk from exposure to vapor of product after combustion.

NOTE

The information contained herein is given in good faith based on our experience, knowledge, and current information, but without guarantee, and the company accepts no responsibility whatsoever for its accuracy and will not be liable for any loss or damage arising there from.